Johnson Controls Electronic Boiler Reset ControlUpgrade to the advantages of a solid state temperature reset controller at a reasonable price!Reset controls provide the optimum water temperature for heating by balancing the delivered hot water temperature to the conditioned space in proportion to the outside air conditions. The colder it gets outside, the hotter the setpoint becomes inside. The outdoor sensor signals the control which adjusts the supply water temperature.
The reset ratio, because it’s electronic, can be set anywhere between 1:5 and 3:1. The A350R is compatible with other System 350 plug-in components so you can add staging, power and display.NOTE: The built-in outdoor cutoff feature is a big money saver because it allows you to select an outdoor temperature where you don’t feel the building needs to be heated.
Once it gets to the outdoor cutoff temperature the occupants can fiddle with thermostats all they want without getting any unnecessary heat! This feature alone makes it an ideal replacement for existing mechanical reset controls, such as the T475 and T678.Specificationss. Power: 24Vac. Reset ratio: 1:5 to 3:1 (indoor:outdoor). Relay: SPST, 4A.
Differential: 1 to 30°F. Sensors: (1) indoor, (1) outdoor (included). Warm Weather Shutdown: OFF, 60°F, 64°F, 68°F, 72°F (jumper selectable). Setback: 0 to 30°F (clock terminals included). Min. How to get good mods warframe.
Johnson Controls System 350 Modular Electronic ControllersUntil now the dependability, accuracy and remote sensing capabilities of electronic controls were expensive and complicated. Now, you can enjoy the benefits of electronic controls without paying for features you don’t want or need. If you need them later, just add them. Stage Adders. System 350 can be tailored to meet the application requirements of each customer.Johnson Controls designed these controls with the convenience of snap-together modularity. A unique five-pin connector makes it possible to add modules quickly and easily without interconnecting wiring.
System 350 units feature DIN rail and wall mount capabilities combined in a single case.Johnson Controls Electronic Temperature Control ModuleAt the heart of the System 350, the A350 temperature control has remote sensing capability up to 800 feet. And it’s accurate to within ±1°F. The A350 Series Controllers are automatic reset electronic temperature controls with a SPDT relay output and LED indication—the LED is illuminated when the relay coil is energized.Features:. Heat/Cool switch.
1 to 30°F adjustable differential. Interchangeable temperature sensors. Selectable direct/reverse actingApplications:.
Frozen/refrigerated food cases. Space temperature control. Cooling tower control sensors. Beverage coolers. Chiller staging.
Johnson Controls Electronic Cooling Control ModuleThe A350E is an on/off electronic cooling only control with SPDT, 10A relay output and LED indication. Besides being a cooling only control, the A350E has two features that differentiate it from the A350: an adjustable minimum setpoint, and short/open circuit protection.Features:.
minimum setpoint selection allows greater control over the cooling system. wide adjustable differential of 1–30°F enables the user to match equipment cycle rate and/or sequencing for a given application. Johnson Controls Electronic Proportional Plus Integral Temperature Control ModuleThe A350P Series Controllers are electronic temperature controls with proportional 0–10Vdc or 0–20mA output. Proportional plus integral control is an option to hold setpoint regardless of load shifts on the system.Features:. surface or DIN rail mounting.
minimum output adjustment. field selectable proportional only or proportional plus integral control. ten segment LED displays percentage of output signal. heat/cool switch allows for reverse or direct acting output. Johnson Controls Staging ModuleThe S350 Staging Modules are used in conjunction with the A350 temperature controls to add multiple stage capability, receiving their power, setpoint and sensor input from the A350 control module.
It has a SPDT output relay and three adjustments, including offset, heating or cooling output, and differential. Up to nine staging modules can be add to the A350 for complete versatility.Applications:.
multiple staging of boilers or chillers. staging of refrigeration compressors. multiple fan staging for cooling tower. Johnson Controls Modular Electronic Sequencer (Click to enlarge)The System 350 ™ R353/S353 Modular Electronic Sequencer is designed to provide multistage control in HVAC/R applications.
Hi, all.Upright freezer conversion begins next week. My Johnson A419 digital thermostat is on it's way, and I'm having an argument with myself about how best to mount it. Form follows function, of course, but I do believe in extra credit for style.:-)All I really want to do is mount it so that the wires are not exposed externally, but I'm a little nervous about drilling through the walls. I'd obviously do due diligence before drilling anything (corn starch/alcohol and all that), but I can't really afford to junk that (old) freezer at the moment. The door is still an option, but that's just going to be a mess inside (true you won't see it with the door closed, but it'll bother me).And so, the first dumb question of many, no doubt:Is there any good reason I shouldn't just mount the display on the inner wall and route power out through the drain?
I've done lots (and lots) of reading on this project (including the A419 manual) and haven't yet seen anyone set up this way.Thanks in advance,Bill. '.power through the drain'? Not sure what that may mean but if there is anything liquid which will be present in that drain, common sense says liquid and electricity never mix well.I have an A419 mounted on the external side of my Kegatronic. Sensor probe snaked in through the back of the unit into the evaporator coil. Electronics are positioned nicely with sheet metal screws.
In all it's a pretty clean installation which you cannot really see because that side of the Kegatronic sets up against the wall.Unless your A419 is the 'weatherproof' model, I wouldn't be sure the cold temperature inside your unit would not be problematic. Another plus to exterior mounting would be easy access to make temperature adjustments if necessary. A LED display can freeze, when that happens they go blank.
Usually when they warm back up they start working again but sometimes not. Forget about the wires and drilling for a moment, were would you consider the desired mounting location to be, top, side or back?
Johnson Controls Thermostat A419 Manual
Since the unit shouldn't be up tight against the wall for heat transfer sake and 3 inches gap is generally advised here, that is also the width of the controller. So one option encompassing form and function would be to mount it on the back side using a L Bracket, with the controller face parallel and flush with the units side. The wires in that case wouldn't be visible since their behind the unit but the controller would be accessible from the side but invisible from the front. If unsightly wires are you concern then you can use cable conduit too. Hi, all.Upright freezer conversion begins next week. My Johnson A419 digital thermostat is on it's way, and I'm having an argument with myself about how best to mount it.
Form follows function, of course, but I do believe in extra credit for style.:-)All I really want to do is mount it so that the wires are not exposed externally, but I'm a little nervous about drilling through the walls. I'd obviously do due diligence before drilling anything (corn starch/alcohol and all that), but I can't really afford to junk that (old) freezer at the moment.
The door is still an option, but that's just going to be a mess inside (true you won't see it with the door closed, but it'll bother me).I would not recommend drilling through the sides if you can avoid it. Typically upright freezers have the condenser coils running through the exterior walls of the unit.
An easy way to tell is to feel the exterior while the unit is running. If the exterior gets warm/hot then don't drill. If you have a set of coils running up the back of the unit or underneath the unit you are probably OK.If you have the space you might try mounting your control similar to where I mounted my Ranco control on my fridge conversion, underneath behind the front grill.
I was able to route the power wires underneath & ran the sensor up through the bottom of the cabinet through a rubber plug. You may or may not have something similar, you will have to look. If your freezer had provisions for an ice maker you might be able to go through where it came through. Here is my set up.
Thanks, guys. Good stuff, but I guess it's tough to make a final decision before I have the thing in my hands.
Johnson Controls A419 Replacement Sensor
Meanwhile, my replies to your replies:@Acmemfg, I just meant that I'd snake male and female power cords out the existing hole in the bottom. The ends would be out on the back somewhere.@pvs6, damage to the unit is exactly what I'm worried about. I didn't see anything in the manual about it either way - maybe I'll call Johnson this week and see what they have to say about it. At the moment though, I'm leaning toward just mounting it on the back with some Velcro. That ought to keep it out of the way and allow me to pull it off easily to make adjustments, etc.@iceman, yes the sides get hot very quickly.
My understanding is that you're supposed to be able to find the lines by using that corn starch & alcohol method, but it makes me nervous anyway. Be just like me to foul that up and junk the whole unit.By the way, that setup is exactly what I meant by extra credit for style. No grill on this unit, unfortunately. I wouldn't worry about it being accessible for making adjustments.When you first install it I am sure you will have to tweak the settings quite a bit to get your keg to your temperature preference.
Once you find the settings that allow for that, you shouldn't have to mess with it anymore, unless you adjust the position of the sensors or you modify your unit with a tower cooler etc etc etc.As long as the variables within the unit don't change - the controller will keep doing it's thing and not need adjustment.
A419 Diagnosis Code
Single-Stage Electronic Temperature Control from Johnson ControlsThe A421 Series single-stage temperature controls are available inlow voltage (24VAC) and high voltage (120 or 240VAC) models. Packed with an A99series PTC temperature sensor with an ambient operating temperature range of-40 to 212⁰F., they provide a Single Pole/Double Throw relay output. The A421series are available with NEMA 1 or NEMA 4X enclosure.